https://www.pinterest.ru/nazirov2128506/pins/ https://www.facebook.com/people/Hand-Madiya/100005653278410 https://www.instagram.com/bagsewtutorial/ 79273134064@yandex.com https://follow.it/diy-tutorial-idease?action=followPub

Zippered Laptop/Tablet Case Sewing Tutorial

Zippered Laptop/Tablet Case Sewing Tutorial

Making a soft sleeve for a tablet. In my case, it’s for an Asus, but you could, of course, make a similar sleeve for any laptop, tablet, or even a mobile phone.

 What you need

fabric for the inside (lining fabric)
fabric for the outside (outer fabric)
Vlieseline H640 (quilted interfacing)
a standard zipper (I used a 30 cm one)
for decoration: a template or shape and Vliesofix (a type of double-sided fusible interfacing)
the dimensions of your tablet
a sewing machine
a standard zipper foot
pins
paper scissors
fabric scissors
matching thread
an iron and ironing board

How to make it

Step 1

Read through the entire set of instructions first. It often makes getting started a bit easier. 

Step 2

First, determine the dimensions of the sleeve. Measure the width, height, and thickness of your tablet. In my case, that’s 19 cm x 27 cm x 1 cm (technically 0.8 cm, but it’s always better to round up).

I’ll start with a 19 cm x 27 cm rectangle. Now, I need to add extra space for the tablet’s thickness and for the seam allowance. 

For the tablet’s thickness, add 1.5 cm all the way around. My tablet is only 1 cm thick, but the thick interfacing (Vlieseline) takes up some space in the finished piece. So, I’m using a 22 cm x 30 cm rectangle. Is your tablet thicker (for example, 2 cm)? If so, add extra space accordingly (e.g., 2.5 cm or 3 cm). 
For the seam allowance, add another 1 cm all the way around. This brings the final pattern size to 24 cm x 32 cm.

Step 3

Draw a rectangle with the correct dimensions (24 cm x 32 cm in my case) onto the fabric and cut it out. You will need a total of 2 rectangles from the outer fabric (red), 2 rectangles from the lining fabric (yellow), and 4 rectangles from the interfacing (Vlieseline).

Make sure to use paper scissors to cut the interfacing; using fabric shears will cause them to become dull.

Step 4

I am using a solid-colored fabric, so I’d like to add some decoration. If you are using a patterned fabric for the exterior, this obviously isn’t strictly necessary—but I wanted to give my cover a fun, extra touch.

To do this, first find a design you like. I’m using a mustache that I recently drew in my notebook; I’ve scaled it up a bit so that it fits nicely on the cover.

Pin the design onto the lining fabric (or another contrasting fabric) and trace along the edge using tailor’s chalk.

Next, cut out the drawing, but do not cut exactly along the outline. Leave some extra space all around; this will make it easier to work with the Vliesofix later on.

Step 5

Place the piece of fabric with the drawing on the Vliesofix and cut out a piece of roughly the same size. Be sure to use your paper scissors for this!

Step 6

Now it’s time for some ironing. First, you need to iron the Vliesofix onto the piece of fabric that features the design. You will notice that Vliesofix has a paper side and an adhesive side (which feels a bit rougher). Place the fabric—design side down—and lay the Vliesofix on top, with the rough side facing down. 

Make sure the Vliesofix doesn’t extend too far beyond the edges of the fabric; otherwise, it will leave a thick layer of adhesive on your ironing board. It is better to cut the Vliesofix slightly smaller than the fabric, while ensuring it is still large enough to cover the design.

If everything is positioned correctly, the paper side of the Vliesofix should be facing up, and you are ready to iron. Follow the same method you would use for regular Vlieseline (fusible interfacing). 

Also, iron the padded interfacing (Vlieseline) onto the fabric rectangles. Follow the same procedure: place the fabric with the right side facing down, position the interfacing on top with the rough side facing down (soft side facing up), and iron it just as you would regular interfacing. 

The difference with the H640 variety is that you should hold the iron in place for 15 seconds instead of 8 seconds; this type of interfacing is significantly thicker than standard interfacing and therefore requires a bit more heat.

If everything has gone according to plan, you should now have 2 quilted rectangles made from the inner fabric, 2 quilted rectangles made from the outer fabric, and 1 small shape with Vliesofix applied.

Step 7

Finish the edges of the four rectangles using a zigzag stitch, an overlock stitch, or an overlocker (serger). While the Vlieseline (interfacing) may help prevent the fabric from fraying excessively, I still prefer to finish the edges of my fabric.

Step 8

Take a rectangle of the lining fabric and lay it on the table with the right side facing up. Then, take the zipper and place it—also with the right side facing up—along the top edge of the rectangle.

Pin the zipper in place, starting from the center and working your way outward to the left and right. When you reach a corner, you will need to make a few small snips into the zipper tape so that it can curve around the corner. You can see what I mean in the photo (as I’m afraid this is a bit difficult to explain in text). Essentially, you need to cut three small notches out of the zipper tape, positioned where the corner of the fabric lies.

Just be careful not to cut too close to the zipper teeth! You still need to be able to stitch the zipper in place without any trouble.

Do the same for the other corner and pin the entire zipper in place.

Step 9

Place a piece of the outer fabric—with the right side facing down—onto the component from Step 8. Ensure the top edges are perfectly aligned and pin them in place. You will need to remove the pins from Step 8 as you go, so that they don’t end up trapped between the layers of fabric.

The most efficient way to do this is to remove one pin and immediately use it to secure the outer fabric. By proceeding one pin at a time, you ensure that the zipper does not come loose again.

Step 10

Stitch along the edge you have pinned, using a zipper foot. If you reach the zipper slider and it gets in the way, leave the needle inserted in the fabric, raise the presser foot, and shift the slider toward the section you have already stitched. Then, lower the presser foot again and continue stitching.

Be careful not to stitch too far. You should only start and stop your stitching where the zipper teeth begin and end. This is because the ends of the zipper need to be tucked into the seam; if you stitch those parts down now, you won’t be able to tuck them in later.

In the photo below, you can see that I actually stitched a bit too far, which meant I had to unpick a small section of my stitching.

Zippered Laptop/Tablet Case Sewing Tutorial

Step 11

Turn the cover right side out so that you can see the zipper again.

Zippered Laptop/Tablet Case Sewing Tutorial

Now, repeat the process from step 9 for the second half of the cover. Place the remaining rectangle of inner fabric on the table, with the right side facing up. Position the zipper on top—also with the right side facing up—and pin it in place.


Once again, you will need to snip small corners out of the zipper.

It’s best to open the zipper all the way; that way, you can work a bit more easily.

Then, place the remaining piece of the outer fabric with the right side facing down and pin it in place.

Step 12

Stitch everything together again using a zipper foot, just as you did in step 10. In the photo below, you can see that I stitched too far, which means the zipper is attached a bit too far along.

Ideally, the zipper should only be stitched up to the piece of clear plastic visible in the photo. Because I stitched too far, I’m unable to tuck that piece of plastic into the seam of the cover. Consequently, I had to unpick a small section of the stitching.

Step 13

Position the cover inside out so that the two layers of the inner fabric have their right sides facing each other, and the two layers of the outer fabric also have their right sides facing each other. Make sure to leave the zipper open by about 10 cm!

Now, we are going to stitch the bottom edges of the inner cover and the outer cover, 1 cm from the edge. Try to stitch as close to the zipper as possible (as shown in the photo below). It’s a bit fiddly, but it can be done if you take your time and work carefully.

Make sure to leave a section open at the bottom of the inner lining so that you can turn the bag right-side out later. 

You can see this in the next two photos, where I’ve left a gap—marked both by pins and by the stitching. For the outer bag, however, you can stitch the bottom completely shut.


Step 14

Turn the entire cover right-side out through the opening in the inner cover.



Close the opening used for turning the piece right-side out by using a blind stitch or by stitching over it with a sewing machine.
 
Zippered Laptop/Tablet Case Sewing Tutorial

Step 15 

 The cover itself is completely finished. Now, all that’s left is to iron my mustache onto the cover.

Zippered Laptop/Tablet Case Sewing Tutorial

First, cut out the drawing using paper scissors.

Then peel the piece of paper off the figure.


Now, iron the figure onto the cover in the same way you would apply interfacing (Vlieseline). Make sure the adhesive side is facing down so that it doesn’t stick to your iron. The adhesive side is the side from which the paper backing is removed (and the side that appears glossier).
 

There you go—a nice tablet sleeve for my better half. My only issue is that I forgot he also has a keyboard that needs to fit in, too. So, I’ll have to make another, larger version.

Good luck with your own version!

 

Zippered Laptop/Tablet Case Sewing Tutorial

Share this :

0 comment:

Post a Comment